X-Series Χ-300 KIT

 

The new X-300 KIT is intended mainly for boats up to 27ft / 9m. For boats with stern drive a special “13 degree” mounting plate is available for a perfect fit.

 

• Size: 300mm
• Stroke length: 50mm
• Mounting plates: 20mm composite or 20mm aluminium
• Transom thickness: Short shaft kit (standard), <80mm transom thickness. Long shaft kit (option), <140mm transom thickness

 

Bureau Veritas approved through-hull design

 

 

Mounting Diagram

 

 

 

 

 

 

 

Kit includes

 

 

 

1.Control Panel: Ergonomic user interface with colour LCD panel and backlit buttons. Sunlight readable with night mode (1 piece)

 

2.NMEA2000 Drop cable 2,5m: Connects to the boats NMEA2000 system or reading GPS data and rudder position. GPS antenna is available as option. (1 piece)

 

3.Control Unit (HCU): The Humphree control unit shall be placed at transom. The servo units and Control panel connects to the control unit. Power cable is included (Cable D). (1 piece)

 

4.Servo Unit: Ultra-fast for unbeatable response and precision. Reliable brushless technology. Waterproof IP67. (2 pieces)

 

5.Interceptor Unit: Robust design with powerful 50mm stroke. Composite material with stainless steel bolts and screws. (2 pieces)

 

Cable A: 10m (Optional extension cable 7m available) (1 piece)

 

Cable C: 4m (2 pieces)

 

 

 

Humphree trim and stabilisation system

Auto Trim, Auto Listings, Coordinated the turn and Active Ride Control. The system increased speed, reduced turning radius and fuel consumption, balanced turns more and reduced the acceleration time significantly.

 

Auto Trim Control

Accelerating and operating at different speeds often means the boat will run with various trim angles. In many situations this results in a poor trim angle, high wave resistance, bad visibility and reduced comfort. Instead of manual adjustment of the Humphree Interceptors, the Automatic Trim Control will give full automatic control of the longitudinal trim by pushing a button.

 

Auto List Control

Uneven loading, cross winds and varying conditions will normally cause the boat to list. When running in a straight course, Automatic List Control will correct the boat list to a preset target list angle, usually zero degrees. This can be changed by the operator to intentionally list the boat. When the boat enters a turn the system will allow the boat to heel naturally during the turn and once the boat has left the turn the system will continue to correct the boat to the preset target list angle

 

Coordinated Turn

For numerous applications the heel angle when turning can be significantly improved to obtain higher speed and increased comfort.The Coordinated Turn Control automatically adjusts the heeling angle of the boat during turns to reduce the side forces for people on board.The system continuously monitors the rudder position during the turn and the Interceptor blade movement is thus automatically coordinated with the rudder movement. With a controlled heel angle, higher turning speeds and better comfort can be achieved.The boat’s turning ability can also be significantly improved as a result of the steering force created by the Interceptor which increases the yaw motion of the boat.

 

Active Ride Control

When operating in open waters wave induced roll and pitch motions onboard vessels usually causes discomfort to all onboard. With a humphree ACTIVE ride control system these motions can be significantly reduced. The ACTIVE system also includes automatic trim and list control moreover compensating for cross winds or uneven loadings – all in one system.

 

 

 

How does it work?

The basic principle of the interceptor trim tab is to create preassure underneath the hull, at the stern of the boat. The pressure is created when the blade is deployed into the waterflow underneath the hull. This lift will change the running trim of the vessel resulting in a lower wave resistance. That is way the interceptor blade need to reach as deep as possible below the boat to create as much lifting force as possible.

 

Humphree has the fastest and longest interceptor blades on the market, which gives a very good result instantly. With interceptor blades of at least 50 mm length moving with accuracy and high speed the movement of the boat will be affected tremendously.

• Reference_Commercial_-_V2V_Empress_-_High_Speed_Ferry.pdf
• Reference_Commercial_-_Queensland_Police_-_Patrol_Catamaran.pdf
• Reference_Commercial_-_Enviro_Cat_-_35m_Ferry.pdf
• Humphree_Interceptors_range_brochure.pdf
• Humphree_Brochure_Leisure.pdf
• Commercial-Steering_Assist-Cat-33m-OMA_Shipyard-MS_Njord.pdf
• Commercial-Cat-24m-Fantasea_sunrise.pdf
• Commercial-Cat-23m-Carbo_Clyde.pdf